CCNP1 ARS110
Three Cisco IOS commands:
neighbor 10.0.0.1
network 10.0.0.2
ping 10.0.0.3
What does 10.0.0.1 mean in the above example?
the peering IGP/EGP router
Three Cisco IOS commands:
• neighbor 10.0.0.1
• network 10.0.0.2
• ping 10.0.0.3
the traffic destination-address
Three Cisco IOS commands:
• neighbor 10.0.0.1
• network 10.0.0.2
• ping 10.0.0.3
What does 10.0.0.3 mean in the above example?
Välj ett alternativ:
the traffic destination-address
What is true regarding GLBP?
Välj ett alternativ:
GLBP can load balance a single vlan across multiple servers
What are the BGP Neighbor Adjacency States ?
Välj ett alternativ:
Idle,connect,active,opensent,openconfirm,established
Matcha ihop värdena:
The metric advertised by our neighbor toward a certain destination
Reported Distance (RD)
Matcha ihop värdena:
The total metric to reach the des tination
Feasible Distance (FD)
Matcha ihop värdena:
The Feasible Successor is the next- hop of the Backup route, in the event that the successor fails
Feasible successor (FS)
Matcha ihop värdena:
Successor is the neighbor chosen to reach a destination, it's the next-hop of the route
Successor Route
Matcha ihop värdena:
To be considerd a backaup route, the reported distance recived form a surten route must be less then the feasible distance caluculated localy
Feasibility Condition
Matcha ihop värdena:
The route with the lowest metric to reach a destination
Successor (S)
What must be understood about the VRRP master when troubleshooting the Virtual Router
Redundancy Protocol (VRRP)?
Välj ett alternativ:
The preempt option must be enabled on the master.
What is true about IGMP Snooping regarding Multicast?
Välj ett alternativ:
The switch listens to IGMP joins sent by clients and adds the group's multicast mac address to the mac address-table for the port it was received on
When using the command route-map xxXxx permit 10, the sequence-number starts at 10. But What happens when you add a new route-map statement without specifying the sequence- number?
Välj ett alternativ:
The sequence-number will increment by 10
Which Multicast address will OSPF use in a none DR/BDR network?
Välj ett alternativ:
224.0.0.5
Which three transitioning techniques are there for IPv4 to IPv6? (Choose 3)
Välj ett eller flera alternativ:
Dual-stack techniques
Translation techniques
Tunneling techniques
What could be a cause of RIB-failure in BGP?
Välj ett alternativ:
That a route with a better administrative distance already exists in the RIB table
How does the routing table reflect the link-state information of an inter-area route?
Välj ett alternativ:
It is marked with O IA
In which order, starting from most preferred to least preferred method will break the tie of what
will become the router ID in OSPF.
Välj ett alternativ:
Router ID, Highest IP address on Loopback, Highest IP address
What is a difference between autonomous APs that operate in a home environment and controller-based APs that operate in a corporate environment?
Välj ett alternativ:
Controller-based APs can be automatically configured and managed by a WLAN controller
What are two benefits of deploying a centralized wireless LAN topology? (Choose two)
Välj ett eller flera alternativ:
maximizing the number of APs that can join a single WLC
convenience of enforcing security policies for all wireless users
What is the role of the fabric edge node in the SD-Access fabric overlay?
Välj ett alternativ:
connecting wired endpoints to the SDA fabric
Which configuration management tool uses an agentless approach?
Välj ett alternativ:
Ansible
What is the function provided by CAPWAP protocol in a corporate wireless network?
Välj ett alternativ:
CAPWAP provides the encapsulation and forwarding of wireless user traffic between an access point and a wireless LAN controller
What does the command "channel-group 1 mode active" do when configured on DLS1 and
DLS2?
Välj ett alternativ:
Enables LACP only if an LACP device is detected
ip route 0.0.0.0 0.0.0.0 209.165.200.241 171
Based on the configuration what was created?
floating static default route
Which network design solotion will best extend layer connectivity to host devices?
Implementing wireless connectivity